Unique wind tunnel test for slower landing approaches
Slower landing approaches by aircraft lead to less noise. How slow, steep and hence quiet a modern commercial aircraft can arrive at a destination airport is determined by the performance of the high-lift system with its retractable slats and flaps on the wings. Another advantage of reduced landing speeds is that shorter runways can be used. The German Aerospace Center (Deutsches Zentrum für Luft- und Raumfahrt; DLR) has joined with Airbus, and the European Transonic Wind Tunnel (ETW) in the three-part project HINVA (High lift INflight VAlidation), consisting of wind tunnel experiments, flight tests and computer simulations. The aim is to combine computer models and wind tunnel tests to substantially improve predictions of high-lift performance and hence pave the way for slower and quieter approach flights. In early February, the project performed unique wind tunnel experiments at cryogenic temperatures in the ETW in Cologne. Equipped with laser measurement technology and other advanced measurement systems, the researchers achieved hitherto unknown precision in detecting the flowfield around an Airbus A320 with extended landing flaps and slats under flight-representative conditions. The researchers had constructed a high precision wind tunnel model specifically for the tests, based on flow measurements performed during in-flight tests with the DLR A320 ATRA research aircraft.
A global first in research
Global GIS Market in the Military Sector 2014-2018
"The HINVA research project is globally unique when it comes to advancing the development of modern high-lift technologies," explains Rolf Henke, a member of the DLR Executive Board and responsible for aeronautics research. “With the A320 ATRA research aircraft, the European Transonic Wind Tunnel and the high-performance TAU computer program, DLR is making use of its unique research infrastructure and deploying its world-leading measurement techniques," continues Henke. Indeed, this is the first time that DLR, in its high-lift research, has combined computer simulations with in-flight and wind tunnel experiments for such a complex configuration.
This unique approach is supported by Airbus as part of its research activities because the desired accurate prediction of the flow features during takeoff and landing are an essential contribution to the optimisation of future aircraft developments. The results of these experiments will be important for the entire aviation industry. " When it comes to new products, the sector will be in a position to plan in greater detail, assessing the deviations between predicted high-lift performance and the actual values," emphasises Henke. "Aeronautics research will acquire valuable insights into how combining the three methods – simulation, cryogenic wind tunnel testing and in-flight testing – can deliver an unprecedented level of precision in aerodynamic analysis and development for commercial aircraft."
An interaction between flaps and gaps
Besides the landing flaps themselves, the gaps that open up between the leading-edge slats, fixed wing and trailing edge flaps play an important role in defining the performance of a high-lift system. All elements must be precisely positioned. Simulating highly complex maximum lift behavior at the limits of the flight envelope remains a daunting challenge for modern computer models. "At DLR, we could make substantial progress with respect to with Computational Fluid Dynamics (CFD) simulations, making use of Europe's largest data centre for aeronautics research, the Center for Computer Applications in Aerospace Science and Engineering (C²A²S²E)," says Cord-Christian Rossow, head of the DLR Institute of Aerodynamics and Flow Technology in Braunschweig. "But to further improve the models we urgently need real flow data from in-flight and wind tunnel tests."
Turbulent flow in laser light
The world’s leading wind tunnel, unique in Europe, offers the capability for testing aircraft under realistic in-flight conditions. The researchers used their measurement equipment to put a dedicated newly manufactured, cryogenic half model of an A320 through its paces. Using a laser measurement technology called Particle Image Velocimetry (PIV) allowed detailed analyses of areas where vortex formation and flow separation occurs. The airflow is not ideal in these zones, prompting complex aerodynamic interference effects that limit the high-lift performance. "The laser measurement technology PIV was developed by our colleagues in Göttingen. We are now able to conduct simultaneous measurements of the flow velocity in many critical areas of the wing," says HINVA Project Coordinator Ralf Rudnik from the DLR Institute of Aerodynamics and Flow Technology. "Therein lies one of the keys to acquire a better understanding of where and why lift breaks down." PIV yielded the first experimental flow field data in a the low speed regime suitable for a direct comparison with in-flight test data and numerical calculations. Classic methods such as force and pressure measurements, alongside modern Stereo Pattern Tracking (SPT) for deformation measurement, Temperature Sensitive Paint for transition detection, and a microphone array for acoustic source location were used to complement these systems.
Flow measurements at 160 degrees below zero
The researchers increased the pressure inside the ETW to 3.3 times atmospheric pressure and cooled the nitrogen flow gas to minus 160 degrees Celsius to deliver the greatest possible precision in replicating real flow conditions for a commercial aircraft. "We evaporated 1281 tons of liquid nitrogen and fed it into the ETW for the HINVA test cycles," reports Guido Dietz, the head of ETW. The wind tunnel has the capability to test models with an onflow speeds up to 1.35 times the speed of sound, but for HINVA, flow speeds just below 0.2 times the speed of sound were used. "Around 30 percent of our tests are now concentrated on investigating high-lift at speeds representative for take-off and landing," Dietz continues. "ETW can produce flight-relevant data under these conditions, while standard wind tunnels most commonly cannot." ETW was developed and constructed by four nations: France, Germany, Great Britain and the Netherlands. DLR acts as Germany’s stakeholder.
Research aircraft as wind tunnel models
The researchers used extensive measurement data collected with the DLR A320 ATRA (Advanced Technology Research Aircraft) over a three-weeks flight test campaign at Airbus in Toulouse in July 2012 to manufacture the A320 wind tunnel model with extraordinarily precise design features. At that time, the scientists, in cooperation with Technische Universität Berlin, equipped the research aircraft with several hundred sensors spread across the entire outer skin. A pressure measurement system using lightweight metal belts attached to the port wing and horizontal stabiliser delivered reliable flow data. The total of 10 test flights pushed the boundaries of the pilots’ skills as they repeatedly approached the aerodynamic limits of the aircraft, initiating stall manoeuvres at low speed.
Further flight campaigns planned
The joint project HINVA receives funding from the German Federal Ministry for Economic Affairs and Energy (Bundesministerium für Wirtschaft und Energie; BMWi) within the framework of its Aviation Research Programme IV. The project is designed to pool national capabilities in the performance evaluation of aircraft for Germany to maintain an international leadership in the field of high-lift research. A second flight campaign with the DLR–ATRA is planned for autumn 2014, within which flight tests are scheduled to measure flow velocity around the wings and flaps during flight. An important step will be the first direct application of PIV laser measurement technology on commercial aircraft. This combination of CFD simulation, wind tunnel experiments and in-flight testing has the potential to yield substantially more accurate predictions of drag values during high speed cruise.
Source : DLR - German Aerospace Center